2018 Ascender Chassis Intake Reinforcement Kit The 2018 ascender chassis has a known defect in the air intake. For 2019 cat added 2 screws in the intake in order to pull the lower intake screens up tight and close the gap that was allowing snow to be sucked into the motor. To... MSRP: Was: Now: $30.00 Add to Cart
Ascender Top of Panel Vent Cover Part of our new line of "STICKY" vents we use a top of the line 3m adhesive sheet to adhere these vents to your sled, no rivets are required making for a low profile clean looking install. High elevation fine powder riders will find this is just... MSRP: Was: Now: $50.00 Add to Cart
Ascender Back of Panel Vent Cover For you high elevation powder riders, the openings cat left in the rear of the side panel can let really fine dry powder into the clutch area. This kit keeps that powder out. Part of our new line of "STICKY" vents, we use a top of the line 3M... MSRP: Was: Now: $40.00 Add to Cart
Ascender Chassis Front of Panel Vents Set of two vents that install on the front edge of each side panel. Great blast of cooling air from this front mounted vents, great addition to our lg side panel vents. Both vents have a fine prefilter material added behind or coarse outer mesh. MSRP: Was: Now: $45.00 Add to Cart
Ascender Chassis Shock Tower Vents Set of two shock tower vents for the ascender chassis cat. Clutch side vent supplies a blast of cold air directly to the primary clutch. Clutch side vent has premium Outwears mesh added behind our coarse outer mesh, clutch side vent should have silicone... MSRP: Was: Now: $40.00 Add to Cart
Ascender Chassis Lg Side Vent Kit Set of two Side vents for your ascender chassis cat. Look factory side panel has the perfect insert for this set of two vents. Fine prefilter mesh installed behind outer coarse mesh, MSRP: Was: Now: $65.00 Add to Cart
Ascender Chassis Headlight Delete Headlight delete for your ascender chassis cat. When developing this delete we incorporated features commonly asked for with our proclimb delete. This new delete has the intake portion of the hood molded into the delete, allowing you to use your goggle... MSRP: Was: Now: $110.00 Choose Options
Ascender Chassis Polycarbonate Hood Lightweight polycarbonate hood for the 2018 up ascender chassis sleds. Hood is designed to be used with the factory front hood "wings" retaining your factory hood color or wrap. Hood by its self weighs in at just under 3 pounds, stock hood... MSRP: Was: Now: $310.00 Choose Options
Proclimb / Ascender Chassis Stock Hood Blockoff plate This block off plate is part of our stock component lightweight hood kit. CNC machined marine grade Hpde plastic has a lip on both sides to seal to the stock center section of the stock hood. Plate is used to make a nose style air intake... MSRP: Was: Now: $30.00 Add to Cart
Proclimb / Procross / Ascender Chassis Defender Air Intake The proclimb/procross chassis airintake tends to suffer water ingestion problems caused by condensation in the large intake track used on the chassis. The Defender intake is a cnc machined plastic plate that bolts onto the nosecone supplying a... MSRP: Was: Now: $110.00 Add to Cart
Wiring harness Proclimb/ and most other sleds Three prong harness for 2012 up cat Proclimb, Ascender chassis without factory LED lights, as well as most other early sleds. Skidoo all sled up to the XM chassis, XP-REV-S2000- Ck-3 ... MSRP: Was: Now: $15.00 Add to Cart
. LED Dual 10 watt cree This is now our LED of choice, this light is a very high quailty led that easily competes with the highest cost lights on the market. These little LEDs are awesome, just the ticket for more than a adequate amount of light to safely... MSRP: $65.00 Was: Now: $45.00 Add to Cart
